Engineered For Toyota Prado

The Prado Bike Rack.

Australia's leading 2-bike and 4-bike rack engineered for the Toyota Prado. Strap-free loading, massive departure clearance, full pivot for rear cargo access, and tested across the harshest tracks Australia has to offer.

Prado 90 Prado 120 Prado 150 Prado 250
Strap-Free Loading Full Rear Pivot Made in Melbourne Lifetime Warranty
Choose Your System
Toyota Prado bike rack 2-bike configuration on Prado 150 series

"Best decision I made for our Prado. Loaded the bikes, locked the handle, drove to Cape York and back. Not a single rattle, not a single strap."

Andrew M. Prado 150 owner, Victoria
Why The iSi Rack For Prado

Engineered For The Prado Adventure.

Generic bike racks weren't designed with the Toyota Prado in mind. iSi is. Every aspect of the system, from the towbar pivot base to the pivot-down geometry, accounts for how Prado owners actually use their vehicle.

Prado-Specific Engineering

The Prado has unique characteristics: a side-hinged barn door at the rear, often a fridge slide or drawer system inside, and owners who actually take it off-road. The iSi rack is engineered for all three.

Side Door Friendly

The Prado's side-hinged rear door swings clear when the rack pivots down, no obstruction. Tilting racks block the door entirely. iSi pivots all the way out of the way.

Fridge Slide Compatible

Pull-out drawers and fridge slides need full clearance behind the vehicle. With the iSi rack pivoted down, your slide extends fully even with bikes on board.

Off-Road Ready

25° or 40° departure clearance protects bikes from rocks and gullies. The shortest possible tow-bar protrusion means you can reverse out of river crossings without dragging.

Prado Compatibility

Fits Every Prado Generation.

All iSi Prado bike racks are engineered for the standard 50x50mm Toyota tow bar receiver installed on every Prado generation from the 90 Series through to the new 250 Series.

Vehicle Compatibility Matrix

Prado Series Years 2-Bike Rack 4-Bike Rack Notes
Prado 90 1996-2002 ✓ Compatible ✓ Compatible Confirm 50x50mm towbar installed
Prado 120 2002-2009 ✓ Compatible ✓ Compatible Standard Toyota towbar receiver
Prado 150 2009-2024 ✓ Compatible ✓ Compatible Most popular Prado fitment
Prado 250 2024+ ✓ Compatible ✓ Compatible New-gen Prado, full clearance
Got a 250 Series Prado?

Check out our Prado 250 / Lexus GX550 specific hitch stabiliser — engineered for the new-gen towbar geometry.

View 250 Stabiliser
The iSi Difference

Completely Strap-Free.

Every other bike rack relies on straps, bungees or tie-downs. iSi doesn't. The wheel cradles and frame supports work in equilibrium so you load your bike, lock the Tee-Handle, and drive. Zero straps.

The Wheel Cradle

Carries 100% Of The Load

Quad Contact wheel cradles grip each tyre at four points on the tread. Every transport load and vibration is handled through the wheels. No movement, no rolling, no straps required.

The Frame Cradle

Zero Load. Just Cradles.

Wide, soft Carbon-Care rubber gently cradles the frame upright. No pressure, no fretting, no paint damage. Safe for carbon, titanium and thin-wall alloy frames.

How It Works

Load. Pivot. Drive.

Loading bikes onto Prado bike rack one wheel at a time
10 Seconds Per Bicycle

Wheel-By-Wheel Loading

Loading one wheel at a time eliminates the need to lift the entire bike. The wheel cradles secure each wheel at four contact points, sharing the bike's weight with the carrier. No ramps required, even for heavy e-bikes. No straps, ever.

  • 10-second load time per bike
  • E-bikes up to 32kg, no ramps required
  • Zero straps or tie-downs in the entire system
Toyota Prado bike rack pivoted down for rear cargo access
15-Second Rear Access

Pivot Down. Bikes Loaded.

The PoziLock latch releases the entire main beam to pivot down, providing full clearance to the Prado's side-hinged rear door, your fridge slide and your drawer system. With or without bikes loaded, in 15 seconds.

  • Full Prado side-door clearance when pivoted
  • Works with bikes on board, no unloading
  • Fridge slide and drawer compatible
Horizontal + Vertical Adjustment

Every Wheel. Every Position.

Wheel cradles slide horizontally for any wheelbase, AND have high/low vertical settings to eliminate handlebar and saddle clashes between adjacent bikes. Carries any combination of road, gravel, MTB, e-bike or fat bike.

  • Wheelbases up to 1,600mm
  • Vertical: high/low per wheel, per end, per bike
  • Zero side-to-side offset for road-legal width
Complete Your Setup

Recommended Add-Ons.

Get more from your Prado bike rack with these popular accessories. Each one is fully compatible with both the 2-bike and 4-bike Prado configurations.

iSi Lightboard System
Compliance

iSi Lightboard System

When bikes cover your Prado's tail lights, the LED lightboard restores brake, indicator and licence plate visibility. Plug-and-play 7-pin connector.

View Lightboard
2-Bike Conversion Pack
Modular

2 ↔ 4 Conversion Pack

Already own one? Add a conversion pack to swap between 2-bike and 4-bike configurations on the same Prado mount. Tool-free swap in seconds.

View Conversion Pack
Caravan Drawbar Mount
Versatile

Caravan Drawbar Mount

Towing a caravan or camper trailer behind the Prado? Add a drawbar mount and swap your carrier between vehicle and trailer in under a minute.

View Drawbar Mount
Wall Mount Storage
Storage

Garage Wall Mount

Hang the carrier on the garage wall when not in use. 20 seconds to un-pin and store, freeing the Prado for Monday morning.

View Wall Mount
Don't drive a Prado?

Use our vehicle finder to get racks engineered for your specific 4WD, ute, EV or passenger vehicle.

Find My Vehicle
Prado Buyer Questions

Frequently Asked Questions.

Common questions from Prado owners about fitment, capacity and use.

Will this bike rack fit my Toyota Prado?

Yes. The iSi Prado bike rack is compatible with all Prado generations: Prado 90 Series (1996-2002), Prado 120 Series (2002-2009), Prado 150 Series (2009-2024), and the new Prado 250 Series (2024+). It connects to the standard 50x50mm Toyota tow bar receiver installed on every Prado.

Can I access the rear of my Prado with bikes loaded?

Yes. The PoziLock pivot mechanism allows the entire rack (with bikes on board) to pivot down for full clearance to your Prado's side-hinged rear door, fridge slide and drawer system. The pivot operation takes around 15 seconds.

Will it carry e-bikes?

Yes. The iSi rack handles bikes up to 32kg each, well above most e-bike weights. The wheel-by-wheel loading method means you don't lift the full bike weight at any point. The 2-bike rack carries 64kg total, the 4-bike rack carries 84kg total.

What's the difference between the 2-bike and 4-bike option?

The 2-bike rack uses a compact main beam optimised for two riders and a tighter rear profile. The 4-bike rack uses a longer beam with stadium-style staggered loading to fit four bikes in the most compact length possible. Both share the same Prado pivot base, and you can buy a Conversion Pack to switch between them later.

Can I swap the rack between my Prado and my caravan?

Yes. Add the iSi Bolt-On Drawbar Mount System to your caravan or camper trailer drawbar, and the same carrier swaps between vehicle and trailer in under a minute, no tools required. Great for base-camping with the trailer and exploring with the Prado.

Is the rack off-road rated?

Yes. iSi racks are field-tested across the harshest Australian terrain including corrugated outback tracks, rock crawling, soft sand and water crossings. The 25° (medium) or 40° (high) departure clearance angle protects bikes from below, and the steel plate construction handles drag-over rocks and gullies.

Will my bikes obscure my Prado's number plate and tail lights?

The pre-configured Prado bike rack includes a licence plate holder. For full compliance with brake lights, indicators and tail lights, we recommend adding the iSi Lightboard System (sold separately) which provides plug-and-play LED replacement lighting via your trailer connector.

How long does the rack take to install?

The pivot base bolts into your Prado's tow bar receiver in about 5 minutes (one person, no special tools). The carrier itself drops onto the pivot base via tool-free pivot pins, taking another 30 seconds. Once installed, you can remove and store the carrier separately in 20 seconds.

Lifetime
Warranty
100%
Australian
Made In
Melbourne
30 Day
Returns

Ready to choose your Prado bike rack?

Pick the 2-bike or 4-bike configuration above, or speak with our team if you're not sure which one suits your Prado system, your bikes and your typical adventures.

Choose Your System